october 2011 doc id 17207 rev 2 1/7 7 STPS200170TV1Y automotive high voltage power schottky rectifier features negligible switching losses avalanche rated low leakage current good trade-off between leakage current and forward voltage drop insulated package: ? electrical insulation = 2500 v rms, ? capacitance = 45 pf aec-q101 qualified description this high voltage schottky rectifier is suitable for high frequency switch mode power supplies. packaged in isotop, this device is intended for use in secondary rectif ication applications. table 1. device summary i f(av) 2 x 100 a v rrm 170 v t j 150 c v f (typ) 0.63 v a1 k1 a2 k2 a1 k1 a2 k2 isotop www.st.com
characteristics STPS200170TV1Y 2/7 doc id 17207 rev 2 1 characteristics when the diodes are used simultaneously: t j(diode1) = p (diode1) x r th(j-c) (per diode) + p (diode2) x r th(c) to evaluate the conduction losses use the following equation: p = 0.5 x i f(av) + 0.0018 i f 2 (rms) table 2. absolute ratings - limiting values per diode at t amb = 25 c, unless otherwise specified symbol parameter value unit v rrm repetitive peak reverse voltage 170 v i f(rms) forward rms current 200 a i f(av) average forward current, = 0.5 t c = 105 c per diode 100 a i fsm surge non repetitive forward current t p = 10 ms sinusoidal 700 a p arm repetitive peak avalanche power t p = 1 s, t j = 25 c 100000 w t stg storage temperature range -55 to + 150 c t j maximum operating junction temperature (1) 1. condition to avoid thermal runaway for a diode on its own heatsink 150 c table 3. thermal parameters symbol parameter value unit r th(j-c) junction to case per diode 0.52 c/w to t a l 0 . 3 1 r th(c) coupling thermal resistance 0.1 dp tot dt j --------------- 1 r th j a ? () ------------------------- - < table 4. static electrical characteristics symbol parameter test conditions min. typ. max. unit i r (1) reverse leakage current t j = 25 c v r = v rrm --200a t j = 125 c - 30 100 ma v f (2) forward voltage drop t j = 25 c i f = 100 a - - 0.85 v t j = 150 c - 0.63 0.68 t j = 25 c i f = 200 a - - 1.01 t j = 150 c - 0.78 0.86 1. pulse test: t p = 5 ms, < 2 % 2. pulse test: t p = 380 s, < 2 %
STPS200170TV1Y characteristics doc id 17207 rev 2 3/7 figure 1. conduction losses versus average current (per diode) figure 2. average forward current versus ambient temperature ( = 0.5, per diode) 0 10 20 30 40 50 60 70 80 90 100 0 20 40 60 80 100 120 p f(av) (w) =0.05 =0.1 =0.2 =0.5 =1 t =t /t p t p i f(av) (a) 0 20 40 60 80 100 120 0 25 50 75 100 125 150 i f(av) (a) t =tp/t tp r th(j-a) =r th(j-c) t amb (c) figure 3. non-repetitive surge peak forward current vesus overload duration (maximum values per diode) figure 4. relative variation of thermal impedance (junction to case) versus pulse duration 0 100 200 300 400 500 600 700 800 1.e-03 1.e-02 1.e-01 1.e+00 i m (a) t c =50c t c =75c t c =125c i m t d =0.5 t(s) 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.e-04 1.e-03 1.e-02 1.e-01 1.e+00 1.e+01 (j ) (j ) =0.1 =0.2 =0.5 single pulse t =tp/t tp z th -c /r th -c t p (s) figure 5. reverse leakage current versus reverse voltage applied (typical values per diode) figure 6. junction capacitances versus reverse voltage applied (typical values per diode) 1.e-04 1.e-03 1.e-02 1.e-01 1.e+00 1.e+01 1.e+02 1.e+03 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 i r (ma) t j =150c t j =125c t j =25c t j =100c t j =75c t j =50c v r (v) 100 1000 10000 1 10 100 1000 c(pf) f=1mhz v osc =30mv rms t j =25c v r (v)
characteristics STPS200170TV1Y 4/7 doc id 17207 rev 2 figure 7. forward voltage drop versus forward current (per diode, low level) figure 8. forward voltage drop versus forward current (per diode, high level) i fm (a) 0 5 10 15 20 25 30 35 40 45 50 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 tj=25c (maximum values) tj=150c (maximum values) tj=150c (maximum values) tj=150c (typical values) tj=150c (typical values) v fm (v) i fm (a) 1 10 100 1000 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 tj=25c (maximum values) tj=150c (maximum values) tj=150c (maximum values) tj=150c (typical values) tj=150c (typical values) v fm (v) figure 9. normalized avalanche power derating versus pulse duration figure 10. normalized avalanche power derating versus junction temperature 0.001 0.01 0.1 0.01 1 0.1 10 100 1000 1 t (s) p p(t p ) p (1 s) arm arm 0 0.2 0.4 0.6 0.8 1 1.2 25 50 75 100 125 150 t (c) j p(t j ) p (25 c) arm arm
STPS200170TV1Y package information doc id 17207 rev 2 5/7 2 package information epoxy meets ul94, v0 cooling method: by conduction (c) recommended torque value: 1.3 nm maximum torque value: 1.5 nm stmicroelectronics strongly recommend the use of the screws delivered with this product. the use of anyother screws is en tirely at the user?s own risk and will invalidate the warranty. in order to meet environmental requirements, st offers these devices in different grades of ecopack ? packages, depending on their level of environmental compliance. ecopack ? specifications, grade definitions and product status are available at: www.st.com . ecopack ? is an st trademark. table 5. isotop dimensions ref. dimensions millimeters inches min. max. min. max. a 11.80 12.20 0.465 0.480 a1 8.90 9.10 0.350 0.358 b 7.8 8.20 0.307 0.323 c 0.75 0.85 0.030 0.033 c2 1.95 2.05 0.077 0.081 d 37.80 38.20 1.488 1.504 d1 31.50 31.70 1.240 1.248 e 25.15 25.50 0.990 1.004 e1 23.85 24.15 0.939 0.951 e2 24.80 typ. 0.976 typ. g 14.90 15.10 0.587 0.594 g1 12.60 12.80 0.496 0.504 g2 3.50 4.30 0.138 0.169 f 4.10 4.30 0.161 0.169 f1 4.60 5.00 0.181 0.197 p 4.00 4.30 0.157 0.69 p1 4.00 4.40 0.157 0.173 s 30.10 30.30 1.185 1.193 f1 f d1 g d s b e1 g1 ?p p1 e e2 g2 c c2 a1 a
ordering information STPS200170TV1Y 6/7 doc id 17207 rev 2 3 ordering information 4 revision history table 6. ordering information order code marking package weight base qty (1) 1. this product is supplied with 40 terminal screws and washers for each tube. the screws and washers are supplied in a separate pack with the order. delivery mode STPS200170TV1Y STPS200170TV1Y isotop 27 g without screws 10 with screws tube table 7. document revision history date revision changes 02-mar-2010 1 first issue. 07-oct-2011 2 added torque values in section 2 .
STPS200170TV1Y doc id 17207 rev 2 7/7 please read carefully: information in this document is provided solely in connection with st products. stmicroelectronics nv and its subsidiaries (?st ?) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described he rein at any time, without notice. all st products are sold pursuant to st?s terms and conditions of sale. purchasers are solely responsible for the choice, selection and use of the st products and services described herein, and st as sumes no liability whatsoever relating to the choice, selection or use of the st products and services described herein. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. i f any part of this document refers to any third party products or services it shall not be deemed a license grant by st for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoev er of such third party products or services or any intellectual property contained therein. unless otherwise set forth in st?s terms and conditions of sale st disclaims any express or implied warranty with respect to the use and/or sale of st products including without limitation implied warranties of merchantability, fitness for a parti cular purpose (and their equivalents under the laws of any jurisdiction), or infringement of any patent, copyright or other intellectual property right. unless expressly approved in writing by two authorized st representatives, st products are not recommended, authorized or warranted for use in milita ry, air craft, space, life saving, or life sustaining applications, nor in products or systems where failure or malfunction may result in personal injury, death, or severe property or environmental damage. st products which are not specified as "automotive grade" may only be used in automotive applications at user?s own risk. resale of st products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by st for the st product or service described herein and shall not create or extend in any manner whatsoev er, any liability of st. st and the st logo are trademarks or registered trademarks of st in various countries. information in this document supersedes and replaces all information previously supplied. the st logo is a registered trademark of stmicroelectronics. all other names are the property of their respective owners. ? 2011 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - philippines - singapore - spain - sweden - switzerland - united kingdom - united states of america www.st.com
|
